Blogger banner

Thursday, April 8, 2010


A light-emitting-diode (LED) is a semiconductor diode that emits light when an electric current is applied in the forward direction of the device, from the anode to the cathode. LEDs are widely used as indicator lights on electronic devices and increasingly in higher power applications such as flashlights and area lighting. 

An LED is usually a small (less than 1 mm) light source. The color of the emitted light depends on the composition and condition of the semiconducting material used, and can be infrared, visible, or ultraviolet.


  • Efficiency: LEDs produce more light per watt, at close to 100 lumens per watt; this is useful in battery powered or energy-saving devices.
  • Colour: LEDs can emit light of an intended colour without the use of colour filters that traditional lighting methods require. This is more efficient and can lower initial costs.
  • On/Off time: LEDs light up very quickly. A typical indicator LED will achieve full brightness in microseconds.
  • Cycling: LEDs are ideal for use in applications that are subject to frequent on-off cycling, unlike fluorescent lamps that burn out more quickly when cycled frequently, Halide lamps that require a long time before restarting.
  • Dimming: LEDs can very easily be dimmed either by modulation or lowering the forward current.
  • Cool light: In contrast to most light sources, LEDs radiate very little heat in the form of infra red that can cause damage to sensitive objects or fabrics. Wasted energy is dispersed as heat through the base of the LED.
  • Slow failure: LEDs mostly fail by dimming over time, unlike the abrupt burn-out of incandescent bulbs.
  • Lifetime: LEDs can have a relatively long useful life. One report estimates 35,000 to 50,000 hours of useful life.
  • Shock resistance: LEDs, being solid state components, are difficult to damage with external shock, unlike fluorescent and incandescent bulbs which are fragile.
  • Focus: The solid package of the LED can be designed to focus its light, the light can be collimated and lensed to any angle. Incandescent and fluorescent sources often require an external reflector to collect light and direct it in a usable manner.
  • Disposabilty: LEDs do not contain mercury and can be easily disposed.
  • Size: LEDs can be very small -just a cubic millimetre and can be packed into small spaces.
  • High price: LEDs are currently more expensive, price per lumen, on an initial capital cost basis, than most conventional lighting technologies. The additional expense partially stems from the relatively low lumen output and the fact that technology is growing very rapidly and huge investments have been made in development with very little time to recover these costs.
  • Temperature dependence: LED performance largely depends on the ambient temperature of the operating environment. Over-driving the LED in high ambient temperatures may result in overheating of the LED package, eventually leading to device failure. This is especially important when considering automotive, medical, and military applications where the device must operate over a large range of temperatures, and is required to have a low failure rate.
  • Voltage sensitivity: LEDs must be supplied with the voltage above the threshold and a current below the rating. This can involve series resistors or current-regulated power supplies.
  • Light quality: Most cool-white LEDs have spectra that differ significantly from the sun or an incandescent light. This can cause the color of objects to be perceived differently under cool-white LED illumination than under sunlight or incandescent sources. However, the color rendering properties of common fluorescent lamps are often inferior to what is now available in state-of-art white LEDs.
  • Blue Hazard: There is increasing concern that blue LEDs and cool-white LEDs are now capable of exceeding safe limits of the so-called blue-light hazard as defined in eye safety specifications.
  • Blue pollution: Because cool-white LEDs emit much more blue light than conventional outdoor light sources such as sodium lamps, the strong wavelength dependence of Rayleigh scattering means that cool-white LEDs can cause more light pollution than other light sources.
As a result of the new developments in LED technology, suddenly from being the humble indicator on the microwave, stereo or washing machine, they are everywhere - 
  • Lighting homes. 
  • In cinemas, discos, malls, 
  • For signage, traffic lights.
  • In torches, medical instruments, cellphones, watches etc.
  • For lighting buildings.
  • In giant TV screens. The list is endless.

Because of the advantages, LEDs hold a theoretical promise that these devices could actually come close to achieving eternal life, converting each watt of electrical energy into pure white light - no infra-red, ultra-violet, no heat, no X-rays. The energy savings will be huge and 50 years on you will still be using the same LED!
Since it is aparent that the LEDs are the future of lighting, huge investments have been made in the development of LED technology. And the result, is the 'Geobulb'.

The GeoBulb is an LED bulb that has been created to replace the normal incandescent bulbs. It supposedly has a 30,000 hour lifespan (which is nearly 10 years), uses only 8w to produce the light of a 60w incandescent, gives out 40% less heat than a CFL and 89% less heat than an incandescent, contains no mercury and instantly lights up on turning it on.  This is indeed the future of lighting. Right now, it is priced high, but the prices are sure to come down with time.
With the rapid progress made in LED technology, the flaws are sure to be corrected, and the LED bulb or LED fluorescent tubelight will replace all the existing incandescent bulbs and Fluorescent tubelights. 

Read more about the different types of LIGHTING LAMPS here:

No comments:

Post a Comment

Thank you for leaving a comment. Will get back to you soon.